*** Chassis Info ***
1 2016 Ford F-550 Regular Cab, Powerstroke Diesel, 2WD, Auto Spec # 5520XLA
VIN # 1FDUF5GT3GEB35463
1 Ford Frame Axle Caps
1 Deweze Clutch Pump Kit for Ford Diesel
1 Utilize Factory Switch Panel
1 Ford 50 Gallon Mid-Ship Fuel Tank – Installed
*** Body Info ***
1 19.5′ Chevron Series 10 Aluminum Car Carrier with independent wheel lift.
Serial # 195C10A05472MD16
10,000lb deck rating, 3,000lb wheel lift rating, Extruded ribbed floor, 2 front/ 6 rear chain locks, 8,000 lb. worm drive winch, 50′
wire rope, roller guide, tensioner, winch free wheel extension, dual control stations, 18 GPM direct mount pump,LED lights
back-up alarm, (2) front safety chains, (1) mechanical anti-tilt, 3,000lb releasable L-arms, (2) wheel lift straps and ratchets, (2)
rear safety chains.
1 Center Mounted Oil Tank
1 Removable steel hand rails
1 Model “H” Bed Mounted Cab Protector (Aluminum Trim) for Dodge 5500/Ford F550
1 Federal Signal 54″ JetStream LED Lightbar with Clear Lenses. Incorporates (12) amber LED modules, (2) Work LIghts, (2) red
LED S/T/T lights. Flat Mount.
1 Upgrade to 9,000lb Warn Winch
1 One pair of additional chain locks installed inthe center of the deck.
1 Installation: (Body) Includes the following: PTO, Plumb Hydraulics, Wire in Lighting through a Common Junction Box . All
08/16/16 13:33:46 www.wreckerbuilder.com Page 1
Wiring will have protective split loom covering and terminated with stainless heat shrink terminals. We also provide a color
coded wiring diagram with the truck.
*** Accessories Info ***
1 Viair Air Compressor – 200 psi capacity – includes 2.0 Gallon Air Storage Tank, pre-wired pressure switch, drain & safety valve.
1 Lodar 2 Function Wireless Remote Control System – This Lodar 2 function system features FETS, wide band, standard output,
standard transmitter and an integrated actuator system.
2 Deck Work Lights – Maxima 4″ Round 9-LED (500 lumen) Work Light with Swivel Mount
* Mounted left & right of winch
2 Lower Work Lights – Maxima 4″ Round 9-LED (500 lumen) Work Light with Swivel Mount
* Mounted on rear tail light housing.
4 16.5″ Quick Mount Tool Box Mount. (Sold as Each)
1 70″ Pro Series Aluminum Tool Box with a Full Shelf Installed
1 70″ Pro Series Aluminum Tool Box with a Half Shelf and Jack Bracket Installed
1 70″ Aluminum Box Top with dividers.
1 70″ Aluminum Box Top (open) without dividers.
2 70″ NARROW Lumber Basket
1 3-In-1 Hook Rack (includes 4 hooks). Modular design. Use as a single unit with 4 hooks or seperate in 3 seperate units. Each
hook has an inside depth of 2.75″ making it right sized to hang hard hats, extension cords, tape rolls, wire rolls and Teflon tape
to name a few.
1 Aluminum Lug Wrench Bracket
4 Pro Series Lower Tool Box Divider 17 1/2″ x 4 1/8″
3 Pro Series Upper Shelf Aluminum Divider 13 1/2″ X 4 1/8″
2 4 Gallon Trash Can
1 One Piece Dual 4 Gallon Trash Can Mount.
2 5 Gallon Aluminum Carrier Liquid Container Mount. This mount will hold (2) 2 gallon liquid containers or (1) 5 gallon liquid
containers on a vertical surface. Works well on the end of a carrier tool box. Caution, it is dangerous to store flammable liquids
on a truck. Please check with your Local, State and Federal Laws before storing flammable liquids on a truck.
1 5 Gallon RED Plastic Liquid Can. Caution, it is dangerous to store flammable liquids on a truck. Please check with your Local,
State and Federal Laws before storing flammable liquids on a truck.
1 5 Gallon YELLOW Plastic Liquid Can. Caution, it is dangerous to store flammable liquids on a truck. Please check with your
Local, State and Federal Laws before storing flammable liquids on a truck.
2 Wire Routing Bracket for Aluminum Pro Series Boxes
36 Duragrid Non Slip Matting Black for toolboxes
1 Strobing Marker & Tail Lights (Body Only)- Installed – This feature will provide strobe capability of the wrecker or carrier Body’s
LED Marker and Rear Tail Lights. Strobe function is controlled by on/off switch in the cab.
4 Interior Tool Box Lighting – Oval 18-LED Light
4 Grommet, Oval
1 Nylon V Bridle With 24″ Legs and Cluster Hooks 5,400lb WLL
1 Chain Bridle with 15″ J Hooks and Hammerhead T-J Combo Hooks
1 8 Point Tie Down System w/ D Ring Short Strap. Incudes (4) Long Straps w/ Chains, (4) Short Straps w/ D Ring, (4) Ratchets
w/ Chain and (1) Carrier Bag
1 Magnetic Tow Lights w/ Round Magnets
1 CHP Kit includes: Tool box, 30 pc. socket set with rails, 7 pc. standard wrench set, 7 pc. metric wrench set, 8″ crescent
wrench, 8″ pliers, 6″ cutters, 6 pc. screwdriver set, duct and electrical tape, tire valve tool, safety glasses, battery brush, hub
cap tool, handy wipes, standard lug wrench, metric lug wrench, 8″ needle nose pliers, 4lb sledge hammer, 18″ bolt cutter, fire
extinguisher, crowbar, broom, shovel. First aid Kit, Triangle Kit, Safety Vest.
1 Wreckmaster Skate Neon (Set of 4)
1 Convert A Ball Case
1 3 Pack Convert A Ball
1 Stream Light Light Box LED Rechargable Flashlight
4 2″ x 12′ Cluster Strap with Mini J, R & T Hooks
1 J Hook with 10′ chain (set of 2)
1 3/8″ x 50ft Swaged Wire Rope with Swivel Hook ( ship factory rope loose with truck)
1 2.5Ton Aluminum/Steel Contruction Racing Style Jack
1 18″ Traffic Cone
1 “Associated Equipment” Flush Mounted Jump Start Socket – Stainless Steel Socket
1 “Associated Equipment” Jump Start Cables – High Quality 25ft. – 500 Amp – Compatible with “Assiciated Equipment” Flush &
Box Socket Assemblies.
1 Carrier Cone Mount – The angle of the mount allows you to quickly access cones from under a fixed deck. The angled cone
mount will hold (6) 18″ traffic cones.